134 lines
3.1 KiB
NASM
134 lines
3.1 KiB
NASM
; sdc
|
|
;
|
|
; Manages the initialization of a SD card and implement a block device to read
|
|
; and write from/to it, in SPI mode.
|
|
;
|
|
; Note that SPI can't really be used directly from the z80, so this part
|
|
; assumes that you have a device that handles SPI communication on behalf of
|
|
; the z80. This device is assumed to work in a particular way.
|
|
;
|
|
; That device has 3 ports. One write-only port to make CS high, one to make CS
|
|
; low (data sent is irrelevant), and one read/write port to send and receive
|
|
; bytes with the card through the SPI protocol. The device acts as a SPI master
|
|
; and writing to that port initiates a byte exchange. Data from the slave is
|
|
; then placed on a buffer that can be read by reading the same port.
|
|
;
|
|
; It's through that kind of device that this code below is supposed to work.
|
|
|
|
; *** Defines ***
|
|
; SDC_PORT_CSHIGH: Port number to make CS high
|
|
; SDC_PORT_CSLOW: Port number to make CS low
|
|
; SDC_PORT_SPI: Port number to send/receive SPI data
|
|
|
|
; Wake the SD card up. After power up, a SD card has to receive at least 74
|
|
; dummy clocks with CS and DI high. We send 80.
|
|
sdcWakeUp:
|
|
out (SDC_PORT_CSHIGH), a
|
|
ld b, 10 ; 10 * 8 == 80
|
|
ld a, 0xff
|
|
.loop:
|
|
out (SDC_PORT_SPI), a
|
|
nop
|
|
djnz .loop
|
|
ret
|
|
|
|
; Initiate SPI exchange with the SD card. A is the data to send. Received data
|
|
; is placed in A.
|
|
sdcSendRecv:
|
|
out (SDC_PORT_SPI), a
|
|
nop
|
|
nop
|
|
in a, (SDC_PORT_SPI)
|
|
nop
|
|
nop
|
|
ret
|
|
|
|
; sdcSendRecv 0xff until the response is something else than 0xff for a maximum
|
|
; of 20 times. Returns 0xff if no response.
|
|
sdcWaitResp:
|
|
push bc
|
|
ld b, 20
|
|
.loop:
|
|
ld a, 0xff
|
|
call sdcSendRecv
|
|
inc a ; if 0xff, it's going to become zero
|
|
jr nz, .end ; not zero? good, that's our command
|
|
djnz .loop
|
|
.end:
|
|
; whether we had a success or failure, we return the result.
|
|
; But first, let's bring it back to its original value.
|
|
dec a
|
|
pop bc
|
|
ret
|
|
|
|
; Sends a command to the SD card, along with arguments and specified CRC fields.
|
|
; (CRC is only needed in initial commands though).
|
|
; A: Command to send
|
|
; H: Arg 1 (MSB)
|
|
; L: Arg 2
|
|
; D: Arg 3
|
|
; E: Arg 4 (LSB)
|
|
; C: CRC
|
|
;
|
|
; Returns R1 response in A.
|
|
;
|
|
; This does *not* handle CS. You have to select/deselect the card outside this
|
|
; routine.
|
|
sdcCmd:
|
|
; Wait until ready to receive commands
|
|
push af
|
|
call sdcWaitResp
|
|
pop af
|
|
|
|
call sdcSendRecv
|
|
; Arguments
|
|
ld a, h
|
|
call sdcSendRecv
|
|
ld a, l
|
|
call sdcSendRecv
|
|
ld a, d
|
|
call sdcSendRecv
|
|
ld a, e
|
|
call sdcSendRecv
|
|
; send CRC
|
|
ld a, c
|
|
call sdcSendRecv
|
|
|
|
; And now we just have to wait for a valid response...
|
|
call sdcWaitResp
|
|
ret
|
|
|
|
; Send a command that expects a R1 response, handling CS.
|
|
sdcCmdR1:
|
|
out (SDC_PORT_CSLOW), a
|
|
call sdcCmd
|
|
out (SDC_PORT_CSHIGH), a
|
|
ret
|
|
|
|
; Send a command that expects a R7 response, handling CS. A R7 is a R1 followed
|
|
; by 4 bytes. Those 4 bytes are returned in HL/DE in the same order as in
|
|
; sdcCmd.
|
|
sdcCmdR7:
|
|
out (SDC_PORT_CSLOW), a
|
|
call sdcCmd
|
|
|
|
; We have our R1 response in A. Let's try reading the next 4 bytes in
|
|
; case we have a R3.
|
|
push af
|
|
ld a, 0xff
|
|
call sdcSendRecv
|
|
ld h, a
|
|
ld a, 0xff
|
|
call sdcSendRecv
|
|
ld l, a
|
|
ld a, 0xff
|
|
call sdcSendRecv
|
|
ld d, a
|
|
ld a, 0xff
|
|
call sdcSendRecv
|
|
ld e, a
|
|
pop af
|
|
|
|
out (SDC_PORT_CSHIGH), a
|
|
ret
|